Materials, Supplies, and Safety

Supplies:

The Basics:
Bound sketchbook, plasticine or fine water based clay of any temperature for maquettes, serrated metal rib and serrated wooden modeling tool, clay shapers, trimming tool, calipers, light plastic (launderers' plastic), misting bottle, small bucket, cut-off wire, needle tool, fork, small sponge, clean up sponge, fabric (uncoated canvas or cotton polyester blend, or muslin (try Goodwill for remnant or old bed sheets), small container for slip, brushes for finishing and decorating, sur-form rasp, exacto knife, Heat Gun or blow dryer and * turntable as work surface (Home Depot or Lowes). * Cover with 2' x 2' piece of 3/4" sealed plywood (required) dust mask and respirator to filter organic vapors (recommended) (try Axner/Laguna Clay or Bennett Pottery or Home Depot).

Specialty Tools (are needed and can be ordered on-line):
1. Kemper Ribbon Sculpting tools (set of 6), available thru Laguna/Axner’s in Florida – 1-800-843-7057, approximately $8.99
2. Sculpture House Wax Modeling tool
Wax Modeling Tool
Item No. SH153 - $14.00 plus shipping

The SH153 wax modeling tool is hand forged and was specifically designed and constructed for use in the delicate art of wax modeling. Also useful for clay modeling and plaster work. Length - 6" is approximate.
http://www.sculpturehouse.com

3. Michael Sherrill red rib, SMT-R1, $6.00 (also suggest yellow rib same price)
http://www.highwaterclays.com/handtools/cooltools2.html#smt

As required for slip casting:
1. Casting slip – Frasier’s Ceramics
2. Large plastic pitcher - Wallmart
3. Larger slotted mixing spoon - Wallmart
4. Kitchen Sieve - Wallmart
5. Large bucket – Wallmart
6. Wooden slats to support molds while draining – found 1.2 x 14” stick will do.

As required for individual projects:
1. Algi-safe ($12.38/ 1lb.from Your Clay Store),
2. Moulding plaster ($.51/ 1lb. from Your Clay Store),
3. Amaco Underglazes – Creative Ceramics in Ocala, website: creativeceramics@embarqmail.com or 352-237-3562
4. Low fire casting slip, Duncan or Mayco Underglazes, vintage decals – Frazier Ceramics in Gainesville, 372-1506

Health and Safety:
Please wear shoes and proper attire, tie back hair and loose clothing when working around shop equipment.

The ceramics program recommends that you wear a respirator when mixing clay and glaze materials and applying glaze with a spray gun. Fowlett’s Bookstore has ordered N95 Filtering Face piece Respirators. Tight fitting respirators can be ordered from Grainger’s or a similar lab safety supply company.

The link for information regarding the SA+AH H&S policy and handbook on health and safety is:. http://www.arts.ufl.edu/art/healthandsafety

2) Each student must complete a H&S STUDENT WAIVER FORM (available next to the copier in the SAAH office) and on-line (see address above). Waivers must be turned into the SAAH Director of Operations before the end of the 2nd week of classes. Please staple the course sheets together.

University of Florida Environmental Health and Safety (EH&S) has determined that the use of respiratory protection is not required for projects and activities typically performed in the School of Art + Art History. It is against the School of Art + Art History policy for any instructor to require students to wear respiratory protection however, you may recommend it, and you may voluntarily choose to wear respiratory protection: either an N95 filtering face piece, commonly known as a dust mask, or a tight fitting half or full-face respirator. Any user who chooses to wear such respiratory protection is therefore said to be a voluntary user. Environmental Health and Safety follows or exceeds OSHA 29CFR1910.132-137 standards for Personal Protective Equipment. Any voluntary user: student, faculty, or staff is required to follow all Environmental Health and Safety policy which can be found at: http://www.ehs.ufl.edu/General/resppol.pdf.
For simplicity, the regulations are outlined below. You must follow each step in order:
1. I want to wear an N95 dust mask. a. Complete “Request for Respirator Use” form (http://www.ehs.ufl.edu/OCCMED/respreq.pdf).

Mail to: Environmental Health & Safety
attn: OCCMED
PO Box 112195
Gainesville, FL 32611
b. Complete “Medical History Questionnaire for N95 Filtering Face piece Respirators” form (http://www.ehs.ufl.edu/OCCMED/N95.pdf) and “UF Voluntary Use Respirator Supplementary Information Memo” (Below) Mail to:

SHCC OCCMED
Box 100148
Gainesville, FL 32611
c. Include Payment: i. There is a $5 charge for the review and processing of this form. 1. Graduate student payment options: a. Enclose a $5 check with drivers license number written on the check
b. Bill to Gator Grad Care by filling out enclosed UF Graduate Student Voluntary Use Respirator Payment Memo

2. Undergraduates must make payment in person. Go to:

Health Science Center
Dental tower, second floor Room D2-49
On the corner of Archer Road and center drive
West entrance
ii. Contact SHCC OCCMED at 352.392.0627 with questions.